Inloggen
Registreren
Notificaties
Knoowy Premium
Verdien geld
Verkoopstatistieken
Uitbetalingen
Studiedocumenten
Oefenvragen
Bundels
Studiebot
Informatie
Instellingen
Uitloggen
Profiel weergeven
Knoowy Premium- Studiedocumenten
Kies een niveau
Categorieën
Studieboeken
- Oefenvragen
Kies een niveau
Opleidingen
Oefenvragen maken
- Studiebot
Rijbewijs C - Vakbekwaamheid - English - Ladingzekering - Cargo securing
Gebruik de 46 oefenvragen om jezelf voor te bereiden en te testen of je de leerstof kent.
Voorbeeld (8 van de 46 oefenvragen)
Kaarten
Schrijven
DownloadWhich statement about gravity is correct?
A. Gravity depends on the average center of gravity in a vehicle.
B. Gravity is determined by the load of a vehicle.
C. Every point in a loaded vehicle has its own center of gravity.
Omdraaien
A. Gravity depends on the average center of gravity in a vehicle.
B. Gravity is determined by the load of a vehicle.
C. Every point in a loaded vehicle has its own center of gravity.
C. Every point in a loaded vehicle has its own center of gravity.
Which statement about kinetic energy is correct?
A. The kinetic energy of an unloaded vehicle is greater than that of a lightly loaded vehicle.
B. The kinetic energy of a vehicle only changes due to changes in the load.
C. Due to kinetic energy, the braking distance increases quadratically when speed doubles.
Omdraaien
A. The kinetic energy of an unloaded vehicle is greater than that of a lightly loaded vehicle.
B. The kinetic energy of a vehicle only changes due to changes in the load.
C. Due to kinetic energy, the braking distance increases quadratically when speed doubles.
C. Due to kinetic energy, the braking distance increases quadratically when speed doubles.
What happens to the center of gravity when a truck is loaded?
A. It becomes higher.
B. It becomes lower.
C. It becomes heavier.
Omdraaien
A. It becomes higher.
B. It becomes lower.
C. It becomes heavier.
A. It becomes higher.
You are driving a tanker on a winding road. Which situation is the most dangerous?
A. The tank is half full.
B. The tank is empty.
C. The tank is full.
Omdraaien
A. The tank is half full.
B. The tank is empty.
C. The tank is full.
A. The tank is half full.
What happens to the load if a truck entrs a roundabout without reducing speed and takes the second exit straight ahead?
A. The load is first pushed to the left, then to the right, and then back to the left.
B. The load is first pushed to the right, then to the left, and then to the right.
C. The load is first pushed to the left, then to the right, then again to the left and right.
Omdraaien
A. The load is first pushed to the left, then to the right, and then back to the left.
B. The load is first pushed to the right, then to the left, and then to the right.
C. The load is first pushed to the left, then to the right, then again to the left and right.
A. The load is first pushed to the left, then to the right, and then back to the left.
What is the effect of sand on the loading floor?
A. Friction increases.
B. Friction decreases.
C. None, as long as I use inti-slip mats.
Omdraaien
A. Friction increases.
B. Friction decreases.
C. None, as long as I use inti-slip mats.
B. Friction decreases.
What is the maximum permitted gross vehicle mass (MTM) of a combination with six axles in Flanders?
A. 40,000 kg
B. 44,000 kg
C. 48,000 kg
Omdraaien
A. 40,000 kg
B. 44,000 kg
C. 48,000 kg
C. 48,000 kg
A lasting strap has the marking SHF = 50 daN. What does this mean?
A. The force that must be manually applied to achieve the pre-tensioning force.
B. The maximum permitted pulling force applied to the strap.
C. The force present in the strap when it is manually tensioned.
Omdraaien
A. The force that must be manually applied to achieve the pre-tensioning force.
B. The maximum permitted pulling force applied to the strap.
C. The force present in the strap when it is manually tensioned.
A. The force that must be manually applied to achieve the pre-tensioning force.
Ontgrendel alle 46 oefenvragen
Koop de oefenvragen en wees voorbereid voor je volgende toets.
In winkelwagenVraag:
Which statement about gravity is correct?
A. Gravity depends on the average center of gravity in a vehicle.
B. Gravity is determined by the load of a vehicle.
C. Every point in a loaded vehicle has its own center of gravity.
Vul het antwoord in:
Controleer antwoordAntwoord:
C. Every point in a loaded vehicle has its own center of gravity.
Jouw antwoord:
input text value
Vraag opnieuw antwoorden
Vraag:
Which statement about kinetic energy is correct?
A. The kinetic energy of an unloaded vehicle is greater than that of a lightly loaded vehicle.
B. The kinetic energy of a vehicle only changes due to changes in the load.
C. Due to kinetic energy, the braking distance increases quadratically when speed doubles.
Vul het antwoord in:
Controleer antwoordAntwoord:
C. Due to kinetic energy, the braking distance increases quadratically when speed doubles.
Jouw antwoord:
input text value
Vraag opnieuw antwoorden
Vraag:
What happens to the center of gravity when a truck is loaded?
A. It becomes higher.
B. It becomes lower.
C. It becomes heavier.
Vul het antwoord in:
Controleer antwoordVraag:
You are driving a tanker on a winding road. Which situation is the most dangerous?
A. The tank is half full.
B. The tank is empty.
C. The tank is full.
Vul het antwoord in:
Controleer antwoordVraag:
What happens to the load if a truck entrs a roundabout without reducing speed and takes the second exit straight ahead?
A. The load is first pushed to the left, then to the right, and then back to the left.
B. The load is first pushed to the right, then to the left, and then to the right.
C. The load is first pushed to the left, then to the right, then again to the left and right.
Vul het antwoord in:
Controleer antwoordAntwoord:
A. The load is first pushed to the left, then to the right, and then back to the left.
Jouw antwoord:
input text value
Vraag opnieuw antwoorden
Vraag:
What is the effect of sand on the loading floor?
A. Friction increases.
B. Friction decreases.
C. None, as long as I use inti-slip mats.
Vul het antwoord in:
Controleer antwoordVraag:
What is the maximum permitted gross vehicle mass (MTM) of a combination with six axles in Flanders?
A. 40,000 kg
B. 44,000 kg
C. 48,000 kg
Vul het antwoord in:
Controleer antwoordVraag:
A lasting strap has the marking SHF = 50 daN. What does this mean?
A. The force that must be manually applied to achieve the pre-tensioning force.
B. The maximum permitted pulling force applied to the strap.
C. The force present in the strap when it is manually tensioned.
Vul het antwoord in:
Controleer antwoordAntwoord:
A. The force that must be manually applied to achieve the pre-tensioning force.
Jouw antwoord:
input text value
Vraag opnieuw antwoorden
Ontgrendel alle 46 oefenvragen
Koop de oefenvragen en wees voorbereid voor je volgende toets.
In winkelwagen
Leer de oefenvragen offline
Leer je de oefenvragen liever vanaf papier? Download dan de 46 oefenvragen als PDF.
In winkelwagen
Binnenkort beschikbaar
€ 4,99
Oefenvragen in winkelwagen
46 oefenvragen beschikbaar
Zelf oefenvragen maken?
Verdien geld met het maken van oefenvragen en leer direct voor je aankomende toets.
Oefenvragen makenInformatie
Every professional driver need to know what forces will work on his load when driving.
Aantal
Taal
Gemaakt opBekijk alle 46 oefenvragen
-
Which statement about gravity is correct?
C. Every point in a loaded vehicle has its own center of gravity.
A. Gravity depends on the average center of gravity in a vehicle.
B. Gravity is determined by the load of a vehicle.
C. Every point in a loaded vehicle has its own center of gravity. -
Which statement about kinetic energy is correct?
C. Due to kinetic energy, the braking distance increases quadratically when speed doubles.
A. The kinetic energy of an unloaded vehicle is greater than that of a lightly loaded vehicle.
B. The kinetic energy of a vehicle only changes due to changes in the load.
C. Due to kinetic energy, the braking distance increases quadratically when speed doubles.
-
What happens to the center of gravity when a truck is loaded?
A. It becomes higher.
A. It becomes higher.
B. It becomes lower.
C. It becomes heavier. -
You are driving a tanker on a winding road. Which situation is the most dangerous?
A. The tank is half full.
A. The tank is half full.
B. The tank is empty.
C. The tank is full. -
What happens to the load if a truck entrs a roundabout without reducing speed and takes the second exit straight ahead?
A. The load is first pushed to the left, then to the right, and then back to the left.
A. The load is first pushed to the left, then to the right, and then back to the left.
B. The load is first pushed to the right, then to the left, and then to the right.
C. The load is first pushed to the left, then to the right, then again to the left and right. -
What is the effect of sand on the loading floor?
B. Friction decreases.
A. Friction increases.
B. Friction decreases.
C. None, as long as I use inti-slip mats. -
What is the maximum permitted gross vehicle mass (MTM) of a combination with six axles in Flanders?
C. 48,000 kg
A. 40,000 kg
B. 44,000 kg
C. 48,000 kg -
A lasting strap has the marking SHF = 50 daN. What does this mean?
A. The force that must be manually applied to achieve the pre-tensioning force.
A. The force that must be manually applied to achieve the pre-tensioning force.
B. The maximum permitted pulling force applied to the strap.
C. The force present in the strap when it is manually tensioned. -
What is 'blocking' (stempelen) a truck?
A. Placing the correct stamps on documents so the truck can be put into traffic.
B. Securing cylindrical cargo using blocks in the loading floor.
C. Stabilizing the truck by extending support beams and placing them on the ground. -
What does the abbreviation MTM means?
A. Minimum Permitted Mass
B. Maximum Permitted Mass
C. Minimum Towing Mass. -
What is axle load?
A. The pressure of an axle with wheels on the load surface.
B. The pressure of an axle on the road surface.
C. The pressure of an axle on the wheel. -
You must deliver goods with a trailer in a country where the MTM for towing is 50,000 kg. You drive through a country where the MTM is 40,000 kg. What do you do?
A. The Belgium MTM appliers, so you may load up to 44,000 kg.
B. You must adhere to the lowest value along your route, so you do not fully load your truck.
C. You may load up to a total mass of 50,000 kg. -
What are the maximum dimensions of a standard truck?
A. Height 3m, width 2.20m, length 12m
B. Height 4m, width 2.55m, length 12m
C. Height 4m, width 2.60m, length 16.50m -
Gasoline has a density of 0.7. What does this mean?
A. 1 liter of gasoline weighs 700 grams.
B. 7 liters of gasoline weigh 1 kilogram.
C. 0.7 liters of gasoline weigh 1 kilogram. -
The coefficient of friction between wood and aluminum is 0.4, and between steel and steel plate 0.2. Which combination will slide the fastest?
A. Wood on aluminum.
B. Steel on steel plate.
C. Both combinations will slide equally fast. -
What is the best way to secure a coil on a truck?
A. With a coil well in the loading floor, and if that is not possible, with wedges or coil cradles.
B. With twistlocks.
C. With filling materials such as airbags or pallets. -
What is the maximum payload of a truck with three axles, with an empty weight of 5,000 kg and n alternative drive?
A. 19,000 kg
B. 22,000 kg
C. 21,000 kg -
What are twistlocks?
A. Devices used to secure containers.
B. Devices used to secure goods in the loading space using internal wall connections.
C. Devices used to secure a coil. -
Which statement about the center of gravity of a vehicle is correct?
A. The center of gravity of a vehicle is fixed.
B. The center of gravity of a vehicle can change depending on temperature.
C. The center of gravity of a vehicle can change depending on the load carried. -
What is the maximum length of a tractor with a semi-trailer?
A. 18.75 m
B. 16.50 m
C. 25.25 m -
Does a tank semi-trailer count as a cargo in a combination?
A. Yes
B. No
C. The tank semi-trailer does not, but its contents do. -
What do we call a pallet with dimensions 80 x 120 cm?
A. An ISO pallet
B. A Euro pallet
C. An IBC pallet -
During an inspection it turns out your truck is overloaded. Who is normally considered responsible?
A. Yourself
B. Your company
C. The loader -
Which forces can act on the load under normal conditions?
A. 0.8 forward, 0.8 backward and 0.5 sideways
B. 0.5 forward, 0.8 backward and 0.5 sideways
C. 0.8 forward, 0.5 backward and 0.5 sideways -
The free space between rectangular cargo and the rear wall can best be blocked with:
A. Blocking beams or shoring bars.
B. Stretch film.
C. Wedges. -
What are wedges?
A. Blocks with a slanted edge used to secure cylindrical loads.
B. Blocks used to secure a container on a trailer.
C. A type of internal wall connection. -
How much hand force is required to achieve the maximum pre-tensioning force of this lashing straps?
A. 50 daN
B. 350 daN
C. 2,500 daN
-- see picture in book page 62 -
Which securing method is generally preferred?
A. Force securing.
B. Form securing (blocking).
C. Neither -
Which statement is correct?
A. The weight of the object is 1,000 kg.
B. The center of gravity of the object is 1,000 kg.
C. The mass of the object is 1,000 kg. -
Which force in a lashing strap is used in direct lashing?
A. LC
B. STF
C. SHF -
What movement do your body and the road make when you perform an emergency stop?
A. A forward movement.
B. No movement.
C. A backward movement. -
What force must a lasting strap on a truck with an MTM of 10,000 kg be able to withstand at minimum?
A. 800 daN
B. 1,000 daN
C. 2,000 daN -
Which statement about tie-down lasting is most correct?
A. in tie-down lashing, the load is pressed onto the loading floor using lashing equipment by tensioning it over the load.
B. Tie-down lashing is equal to securing the load with a loop on the side of the truck.
C. Tie-down lashing is done by directly attaching the load to the lashing equipment. -
Which film must you heat so that the plastic adheres to the load unit?
A. Stretch film.
B. Wrapping film.
C. Shrink film. -
What are the strongest forces a load can experience at sea?
A. Mainly forward forces.
B. Mainly backward forces.
C. Mainly forces perpendicular to the length of the ship. -
Which country is the strictest regarding load securing?
A. Belgium.
B. Greece.
C. Germany. -
Which angle between the lashing strap and the loading floor gives the best result for tie-down lashing?
A. Between 10° and 55°
B. 45°
C. 90° -
What force must a standard headboard of a truck that complies with the EN standard be able to withstand?
A. 40% of the MTM, with maximum of 5,000 daN.
B. 40% of the payload, with a maximum of 5,000 daN.
C. 40% of the payload, with maximum of 3,000 daN. -
What is the unit of weight?
A. Newton
B. Gram
C. ton -
You apply a tie-down lashing to a pallet with this lashing strap (see book). With what force is the load pressed against the loading floor?
A. 50daN
B. 350daN
C. 2,500 daN
-- see picture in book page 63 -
Case 1
You are driving a tractor and a semi-trailer. The MTM of the tractor is 18,000 kg, the MTM of the semi-tractor is 37,000 kg. You are transporting a load packed in IBCs (intermediate Bulk Containers) -
Case 1
You are driving a tractor and a semi-trailer. The MTM of the tractor is 18,000 kg, the MTM of the semi-tractor is 37,000 kg. You are transporting a load packed in IBCs (intermediate Bulk Containers)
1. What is the maximum MTM of the combination in Europe?
A. 55,000 kg
B. 44,000 kg
C. 40,000 kg -
Case 1
You are driving a tractor and a semi-trailer. The MTM of the tractor is 18,000 kg, the MTM of the semi-tractor is 37,000 kg. You are transporting a load packed in IBCs (intermediate Bulk Containers)
2. What force occurs when accelerating on a straight road?
A. Forward force
B. Backward force
C. Centrifugal force -
Case 1
You are driving a tractor and a semi-trailer. The MTM of the tractor is 18,000 kg, the MTM of the semi-tractor is 37,000 kg. You are transporting a load packed in IBCs (intermediate Bulk Containers)
3. For which types of cargo are IBCs mainly suitable?
A. Bulk goods such a powders and granulates, an liquids.
B. General cargo
C. Food products -
Case 1
You are driving a tractor and a semi-trailer. The MTM of the tractor is 18,000 kg, the MTM of the semi-tractor is 37,000 kg. You are transporting a load packed in IBCs (intermediate Bulk Containers)
4. Where can you find information about your truck, such a maximum axle loads?
A. On the technical sheet.
B. On the inspection certificate.
C. On the certificate of conformity. -
Case 1
You are driving a tractor and a semi-trailer. The MTM of the tractor is 18,000 kg, the MTM of the semi-tractor is 37,000 kg. You are transporting a load packed in IBCs (intermediate Bulk Containers)
5. On your route encounter several roundabouts. Which forces must you take into account?
A. Forward forces when approaching the roundabout, because you need to brake.
B. Lateral forces when driving on, entering, and exiting the roundabout.
C. Both A and B
Verkoper
- 7 oefenvragen gemaakt
Gerelateerde oefenvragen
64 oefenvragenAl meer dan 146.000 tevreden studenten
-
hancapaIk heb Knoowy voor het eerste keer gebruikt. Het heeft me geholpen en ik raad het aan om eens uit te proberen.
-
Pinjeu
Prima service, snelle afhandeling. Ik ga hiervan gebruik maken gedurende mijn hele studie.
-
IneMatheeussen
Grote hulp voor het nakijken van taken! Zeker wanneer je in tijdsnood zit of niet zeker bent van je stuk.
-
febeh
Betrouwbare website. Helpt me goed bij het studeren en herhalen.
-
Gulcin Gulcin
Ik raad Knoowy iedereen aan, die extra hulp nodig hebben bij hun opdrachten!
-
Worryworry
Een aanrader om documenten te laten nalezen. Er is ook de keuze om samenvattingen te gebruiken van anderen en dat is handig.
-
Bente Heyrman
Het uploaden en verkopen van mijn documenten verloopt altijd super vlot, alles word eigenlijk al door Knoowy geregeld! Leuk dat medestudenten ook iets aan mijn documenten hebben!
-
Olivier
Prima samenvattingen van veel verschillende vakken die je goed kunt gebruiken.
Eerder bekeken door jou
downloadsVerkoop samenvattingen en andere studiedocumenten
Document uploaden
Overhoor jezelf en verdien geld met zelfgemaakte oefenvragen
Oefenvragen maken
Hoe het werkt
Verdien geld
Koop en verkoop samenvattingen en andere studiedocumenten voor: Universiteit - Hogeschool - Secundair onderwijs - Studieboeken
Ondersteuning bij het leren: Oefenvragen leren - Oefenvragen maken - Stel een studievraag - Studiebot antwoorden
- Nederlands - € (EUR)
Actie: ontvang 10% korting bij aankoop van 3 of meer items!
Actie: ontvang 10% korting bij aankoop van 3 of meer items!
